Product Name:  
Vacuum/Sensor Blocks  
Vacuum/Sensor Blocks  
TS-0704-1XXX  
Product Description:  
Product Number:  
-
-------------------------------------------------------------------------------  
AB
Th Vacuum/Sensor Block. These models have some great features. These include:  
•
TS-0704-1101/1201/13016 (ONLY) 1/8 NPT Ports for such applications as  
o
o
o
o
o
o
Fuel Pressure Sensor  
Manifold Pressure Sensor  
Wastegate  
Blow Off Valve  
Boost Gauge  
Brake Booster  
IMPORTANT NOTES ON YOUR MANIFOLD BLOCK  
•
Use only high quality hose and fittings that is the correct size and pressure rating for your application when fitting your manifold – other  
hoses will be affected by heat and will eventually crack or split which could cause excessive boost pressure and engine damage  
Ensure that all plumbing is secured with clamps or cable ties.  
•
•
Your Sensor /Vacuum Blocks should be mounted at least 100mm from any heat source  
RECOMMENDATIONS`  
•
Turbosmart recommends that once installed the part is correctly mounted as well as checked for any possible leaks.  
-
-----------------------------------------------------------------------------------------------------------------------  
HOW TO INSTALL YOUR SENSOR BLOCK  
TOOLS REQUIRED  
General mechanic tools  
Part  
Description  
1
2
3
4
5
Sensor Block/s  
1/8 NPT Nipple  
1/8 NPT Blank  
Mount/Associated Parts  
M3/6 Mounting Screws  
TS-0704-1201 Pictured  
1
TS-0704-1101  
Vacuum Distribution Block Base Kit 6 Way 1/8 NPT  
•
•
2 x Mounting Blocks  
6 x Vacuum Block 1/8 NPT Ports (Shared)  
TS-0704-1201  
TS-0704-1301  
Remote Sensor Block Base Kit 3 Way 1/8 NPT  
Sensor and Vacuum Distribution Base Combo Kit Single Sensor 1/8 NPT  
•
•
2 x Mounting Blocks  
3 x Sensor 1/8 NPT Ports (Input and Sensor)  
•
•
•
2 x Mounting Blocks  
2 x Sensor 1/8 NPT Ports (Input and Sensor)  
4 x Vacuum Block 1/8 NPT Ports (Shared)  
1
INSTALLING VACUUM/BOOST MANIFOLDS  
Mounting Boost/Vacuum Manifold  
Internal Plumbing Logic  
1
2
The Boost/Vacuum Manifolds are easily mounted using  
the supplied hardware. The user can decide where the  
most suitable location or mount using existing brackets  
or fabricate a more suitable mount.  
TS-0704-1101  
This vacuum block is shared over the 6 x 1/8 NPT  
Inputs. (All common)  
Mount Options:  
TS-0704-1101/TS-0704-1201/TS-0704-1301  
Mount using the supplied M6 Bolts and spacers if  
TS-0704-1201  
This sensor block is setup for 3 Inputs and 3 Sensors  
TS-0704-1301  
This sensor block is setup for 2 Inputs and 2 Sensors  
1
Installing Gauges and Fittings  
Optional Expanding Sensor and  
Manifold Blocks  
3
5
Gauges and fittings will need to be applied to utilise the  
manifold. Each variation has slightly different internal  
logic.  
The Sensor TS-0704-1X01 range are expandable to  
allow for more blocks to be added to the existing change  
of blocks depending on the required setup.  
Vacuum Manifolds are common and share all ports.  
Sensor ports have an input and output (sensor).  
Familiarise yourself with the internal plumbing logic.  
Noted in step 2/  
The blocks are simply located in with a M4 bolt and O  
Ring that ensure a snug fit of the chain of blocks. The  
Block is terminated with a mounting block on the end of  
the chain.  
Apply thread lubricant and screw in clockwise until  
finger tight, then tighten further 1-2 turns for seal.  
Start engine and check for leaks  
4
Congratulations, your manifold block is installed and  
ready for use. Double check all fittings, lines and  
mountings then proceed to watch for any leaks.  
CAUTION!  
If leaks are present – switch off engine immediately  
and rectify leaks.  
CAUTION!  
Ensure to not damage O rings as these are used to  
seal on Vacuum Blocks.  
-
--------------------------------------------------------------------------------------------------------------------  
TROUBLE SHOOTING  
The following points should be checked if you find that your Vacuum/Boost Manifold is leaking  
•
•
Check for O rings between blocks are intact  
Check that the NPT threads are correctly torqued to a point that seals using the tapered thread.  
2